Mark Janssen and Zac Adelman, LADCO
November 2026
Ground-level ozone remains one of the most persistent regional air quality problems in the United States, and volatile organic compounds (VOCs) play a central role in its formation. Ozone precursor emissions control programs historically treated all VOCs as equally important, regulating them on a simple mass basis, e.g., tons of VOC reduced, without regard to how efficiently any compound forms ozone in the atmosphere. As atmospheric chemistry models and measurements improved, it became clear that some VOCs, such as highly reactive olefins and aromatics, can form several times more ozone per unit mass than relatively inert compounds such as methane or acetone [1,2]. This insight led to the development of quantitative reactivity scales, most prominently the Maximum Incremental Reactivity (MIR) scale, which expresses the grams of ozone formed per gram of VOC added under high nitrogen oxide (NOx) conditions, where ozone formation is most sensitive to VOC [1,3].
Using VOC reactivity as the basis for control allows regulators to focus limited resources on the compounds that matter most for ozone, while giving industry flexibility to reformulate products and processes using lower-reactivity alternatives [4]. Instead of simply capping total VOC content, a reactivity-based program can reward substitution of solvents with low MIR values, encourage the use of exempt compounds with negligible reactivity, and target the most ozone-productive species such as ethylene, propylene, and aromatic solvents. Over the last two decades, several states and federal agencies have incorporated reactivity concepts into regulations for aerosol coatings, fuels, industrial sources, and, on a limited basis, consumer products. Several of these controls are in effect in California and Texas, and federal rules extend reactivity-based control nationwide. This white paper summarizes the regulatory programs that have used VOC reactivity to reduce ozone concentrations.
Reactivity-Based Limits for Aerosol Coatings
Some states regulate aerosol coatings using reactivity-based limits that cap each product category’s product-weighted MIR, rather than its total VOC content, for coatings such as primers, enamels, metallic finishes, and specialty aerosols [5,6].
Under this approach, each VOC ingredient is assigned an MIR value in grams of ozone per gram of VOC, and the product-weighted MIR is calculated by multiplying each compound’s weight fraction by its MIR and summing across the formulation; compliance is demonstrated when the product-weighted MIR is below the category limit [5]. Highly reactive aromatics such as xylene mixtures, with MIR values around 7 g O₃/g VOC, and toluene, at roughly 4 g O₃/g, have strong upward leverage on product reactivity, while lower-reactivity solvents such as propane (about 0.5 g O₃/g) and acetone (about 0.4 g O₃/g) provide opportunities to reduce ozone formation without eliminating solvent functionality [2].
These changes are now common in aerosol and protective coatings sold nationwide in markets where California Air Resources Board (CARB) and U.S. Environmental Protection Agency (EPA) reactivity-based limits apply, effectively turning reactivity into a design parameter for industrial products.
CARB’s aerosol coating rule has been in effect statewide since the early 2000s [6].
National Reactivity-Based Standards for Aerosol Coatings
EPA adopted nationwide VOC standards for aerosol coatings in 2008 under Clean Air Act section 183(e). The rule sets product-weighted reactivity (PWR) limits for each coating category instead of mass-based VOC caps [7,8].
The federal rule follows the California framework. Each ingredient carries a reactivity factor drawn from the MIR scale, and a product’s PWR is the sum of each ingredient’s weight fraction multiplied by its reactivity factor [2,8]. Category limits push formulators away from high-reactivity aromatics and olefins while allowing continued use of lower-reactivity solvents such as acetone. EPA added compounds to its table of reactivity factors in 2012 [9].
In January 2025, EPA finalized a major update to the rule. The amendments revised category PWR limits, added new compounds and reactivity factors, and updated existing reactivity factors [10]. EPA later moved the compliance date for the amended requirements from July 17, 2025, to January 17, 2027 [11].
The rule also builds reactivity into product labels. Each label must show the product’s category code, the applicable PWR limit, the manufacture date or a date code, and contact information for the regulated entity [7]. Printing the PWR limit on the label makes the reactivity basis of compliance visible to distributors, inspectors, and users.
Reactivity Provisions in California’s Consumer Products Regulation
California’s consumer products regulation remains mass-based. CARB sets VOC limits, expressed as a percent of product weight, for dozens of product categories [12]. Aerosol coatings are the exception, and CARB regulates them separately under its reactivity-based aerosol coating rule (Section 1) [5].
CARB added a narrow reactivity pathway in its 2021 amendments. The amended Innovative Products Exemption (Section 94511) applies to hair finishing sprays, dry shampoos, and personal fragrance products [13]. A manufacturer can qualify a product that uses an alternative propellant system if it compares favorably with a designated representative product, using product-weighted MIR to show that the new product does not increase ozone-forming potential [2,13]. The provision’s main goal is to cut emissions of hydrofluorocarbon (HFC) propellants, which have high global warming potential; MIR serves as the guardrail against ozone disbenefits. Industry commenters supported the MIR basis and urged CARB to extend it to other categories [13].
CARB appears ready to go further. Trade reporting on CARB’s 2023 Consumer and Commercial Products Survey, released in October 2026, indicates that CARB will likely use MIR values to regulate categories in its next consumer products rulemaking, which would be the first broad use of reactivity in the program [14]. The survey ranks categories both by VOC mass and by ozone formation, and the two rankings differ. Hand sanitizer and non-aerosol multi-purpose solvents top the mass list, while hand and body lotions, non-aerosol general purpose cleaners, and laundry detergents top the ozone formation list [14]. This divergence is the core argument for reactivity-based control: the categories that emit the most VOC by mass are not necessarily those that form the most ozone.
Reactivity-Adjusted Controls for Reformulated Gasoline
California’s Phase 3 reformulated gasoline (RFG) regulations let refiners certify alternative fuel formulations using the California Predictive Model. The model predicts how a candidate fuel changes vehicle emissions relative to a reference fuel [15].
Under the model’s exhaust-and-evaporative option, predicted changes in exhaust hydrocarbons, evaporative hydrocarbons, and carbon monoxide (CO) are combined into a single change in ozone-forming potential [15]. Evaporative hydrocarbons carry a reactivity adjustment factor that reflects the greater ozone-forming potential of exhaust emissions, and CO enters through its own adjustment factor [15]. A candidate fuel qualifies if its predicted changes in ozone-forming potential, NOx, and potency-weighted toxics each stay at or below 0.04 percent relative to the reference fuel [15].
Framing compliance in reactivity-weighted terms rather than hydrocarbon mass gives refiners controlled flexibility. They can offset changes in lower-reactivity evaporative emissions against changes in more reactive exhaust emissions, provided total ozone-forming potential does not rise. CARB adopted these procedures in 2000 and amended them in 2001 [15].
VOC Exemptions for Low-Reactivity Compounds
One of the most pervasive reactivity-based controls in the United States is the long-standing policy of exempting organic compounds with negligible ozone-forming potential from the regulatory definition of VOC, effectively allowing their use as substitutes for more reactive solvents [16,17].
EPA compares the reactivity of candidate compounds to that of ethane, whose MIR is on the order of 0.3 g O₃/g VOC, and designates compounds with even lower reactivity, such as methane, acetone, and certain hydrofluoroolefins, as VOC-exempt for ozone control purposes [2,4,18,19]. State and local air districts, including the South Coast Air Quality Management District (SCAQMD) in Southern California, incorporate these exemptions into coatings and solvent rules, sometimes further screening candidates for toxicity or other environmental impacts [20]. By shifting product formulations from high-MIR species like xylene to exempt or low-MIR solvents, regulated sources can achieve meaningful reductions in ozone-forming potential even when total organic content remains similar.
Highly Reactive VOC Emission Limits in the Houston–Galveston–Brazoria Region
Texas has adopted special emission limits for Highly Reactive Volatile Organic Compounds (HRVOCs) in the Houston–Galveston–Brazoria (HGB) ozone nonattainment area, recognizing that a small subset of VOCs contributes disproportionately to local ozone formation [21,22].
The HRVOC rules target compounds such as ethylene, propylene, 1,3-butadiene, and butenes, which have high MIR values and react rapidly with atmospheric oxidants, by imposing stringent controls on emissions from flares, process vents, cooling towers, and fugitive components at petrochemical and refining facilities [21,23]. By distinguishing HRVOCs from less reactive VOCs, the rules ensure that industrial sources in the HGB region prioritize reductions from the most ozone-productive emissions, providing a reactivity-focused complement to broader mass-based VOC controls elsewhere in the state.
HRVOC Emissions Cap-and-Trade in Harris County, Texas
As a companion to source-specific limits, Texas operates the Highly Reactive Volatile Organic Compound Emissions Cap-and-Trade (HECT) program, which establishes an annual cap on HRVOC emissions from certain facilities in Harris County and allows trading of HRVOC allowances [21,24].
Because the program focuses solely on a set of very reactive olefinic compounds, it is inherently reactivity-based: each ton of HRVOC reduced under the cap yields a much greater reduction in ozone formation than a ton of average VOC. Facilities that can achieve deep reductions in ethylene, propylene, and related HRVOCs generate surplus allowances, while those with more limited control options must purchase allowances, effectively channeling investment into the most cost-effective HRVOC controls [25]. The HECT program has been implemented for several years as part of the Houston–Galveston–Brazoria ozone State Implementation Plan and remains a prominent example of reactivity-targeted emission trading.
Short-Term Limits and Flare Monitoring for Highly Reactive VOCs
The HRVOC rules do not set unit-specific emission rates. The Texas Commission on Environmental Quality (TCEQ) describes them as performance-based, with emphasis on monitoring, recordkeeping, reporting, and enforcement [21]. Their main short-term control is a site-wide cap: HRVOC emissions from any flare, vent, pressure relief valve, cooling tower, or combination of these may not exceed 1,200 pounds in any one-hour block [23]. Measurements during the Texas 2000 Air Quality Study showed that petrochemical plumes rich in ethylene and propylene form ozone faster and more efficiently than urban or power plant plumes [22], so even brief HRVOC releases matter.
Flares receive particular attention because they handle large HRVOC streams. The rules require flare monitoring so that HRVOC emissions can be quantified, and those emissions are calculated assuming 99 percent destruction for ethylene and propylene and 98 percent for other HRVOCs [23,26]. TCEQ emissions inventory guidance allows the 99 percent value only for compounds of three or fewer carbon atoms that contain only carbon and hydrogen [27]. These values are accounting assumptions, not demonstrated performance. Because a flare at 98 percent destruction emits twice as much as one at 99 percent, small shortfalls in flare performance carry outsized weight in the HGB ozone strategy.
Reactivity-Informed Controls for Architectural and Industrial Maintenance Coatings
While many architectural and industrial maintenance (AIM) coating rules remain formally mass-based, they increasingly rely on reactivity-informed choices of exempt compounds and solvent systems, especially in regions such as California that make extensive use of MIR data [3].
Regulators and industry guidance documents for AIM coatings routinely highlight the high MIR values of aromatic solvents like xylene and the benefits of replacing them with blends of oxygenated solvents and aliphatic hydrocarbons that provide similar solvency at markedly lower ozone-forming potential [2,28]. As states tighten AIM VOC limits and consider future updates, MIR-based evaluations of candidate solvent systems have become an important tool for ensuring that nominal VOC reductions translate into real decreases in ozone exposure.
Reactivity-Weighted Industrial Control Strategies in EPA and State Implementation Plans
States and EPA use MIR and related reactivity scales in their ozone industrial source State Implementation Plan (SIP) modeling to prioritize VOC controls that deliver the greatest ozone benefit per ton of reduction, even when the formal regulations are framed in mass terms [4].
In these planning exercises, emissions from different source categories, such as on-road gasoline vehicles, solvents, and petrochemical facilities, are reweighted by representative MIR values for their VOC mixtures, allowing regulators to see that reductions in highly reactive mixtures can be several times more effective than equivalent mass reductions from low-reactivity sources [1,25]. This reactivity-weighted perspective has influenced the selection of control measures in California, Texas, and other nonattainment areas, steering attention toward sectors rich in olefins and aromatics while still supporting broad-based VOC reductions.
EPA’s ongoing process of evaluating and, where appropriate, exempting new low-reactivity organic compounds from the VOC definition is itself a reactivity-based ozone control strategy, as it shapes the menu of substitutes available for reformulation of solvents, refrigerants, and blowing agents [4,16].
In recent years, the agency has considered and, in several cases, approved exemptions for halogenated olefins and hydrofluoroolefins whose MIR values are below that of ethane [19,29–31], signaling that their incremental contribution to ground-level ozone is minimal. As these compounds enter the marketplace, they allow industries ranging from aerosols to foam manufacturing to replace higher-MIR hydrocarbons with functionally similar but much less ozone-productive chemicals, extending the reach of reactivity-based control into emerging product sectors across the United States.
Conclusions
Taken together, these examples illustrate how photochemical reactivity has moved from an academic concept to a practical organizing principle for VOC control in the United States. By quantifying the ozone-forming potential of individual compounds and mixtures, regulators can distinguish between emissions that are merely large in mass and those that are genuinely important for peak ozone episodes, enabling more cost-effective and environmentally meaningful control programs.
Reactivity-based controls do not replace traditional VOC regulations, but they refine them, tightening limits where they matter most, rewarding the use of low-MIR solvents and exempt compounds, and focusing special attention on highly reactive olefins and aromatics from key industrial and consumer product sources. As atmospheric chemistry continues to evolve and new compound classes enter commerce, the MIR framework and related reactivity metrics will remain central tools for designing ozone strategies that are scientifically grounded, flexible for industry, and protective of public health in ozone nonattainment regions across the country.
References
[1] Carter, W.P.L. (1994). Development of ozone reactivity scales for volatile organic compounds. Journal of the Air & Waste Management Association, 44(7), 881–899. https://doi.org/10.1080/1073161X.1994.10467290
[2] California Code of Regulations, Title 17, §§ 94700–94701. Tables of Maximum Incremental Reactivity (MIR) Values. Operative October 2, 2010; amended January 1, 2015, and August 1, 2022. https://www.law.cornell.edu/regulations/california/17-CCR-94700
[3] Carter, W.P.L. (2010). Updated Maximum Incremental Reactivity Scale and Hydrocarbon Bin Reactivities for Regulatory Applications. Report to the California Air Resources Board, Contract 07-339. College of Engineering Center for Environmental Research and Technology, University of California, Riverside. https://intra.engr.ucr.edu/~carter/SAPRC/MIR10.pdf
[4] U.S. Environmental Protection Agency (2005). Interim Guidance on Control of Volatile Organic Compounds in Ozone State Implementation Plans. 70 Fed. Reg. 54046 (September 13, 2005).
[5] California Code of Regulations, Title 17, §§ 94520–94528. Regulation for Reducing Ozone Formed from Aerosol Coating Product Emissions. California Air Resources Board.
[6] California Air Resources Board (2001). Updated Informative Digest: Adoption of Amendments to the Regulation for Reducing Volatile Organic Compound Emissions from Aerosol Coating Products and Tables of Maximum Incremental Reactivity (MIR) Values. https://ww2.arb.ca.gov/sites/default/files/barcu/regact/conspro/aerocoat/uid.pdf
[7] Code of Federal Regulations, Title 40, Part 59, Subpart E. National Volatile Organic Compound Emission Standards for Aerosol Coatings (§§ 59.500–59.516). https://www.ecfr.gov/current/title-40/chapter-I/subchapter-C/part-59/subpart-E
[8] U.S. Environmental Protection Agency (2008). National Volatile Organic Compound Emission Standards for Aerosol Coatings; Final Rule. 73 Fed. Reg. 15604 (March 24, 2008).
[9] U.S. Environmental Protection Agency (2012). National Volatile Organic Compound Emission Standards for Aerosol Coatings: Addition of Dimethyl Carbonate, Benzotrifluoride, and Other Compounds to Table of Reactivity Factors. 77 Fed. Reg. 14279 (March 9, 2012).
[10] U.S. Environmental Protection Agency (2025). National Volatile Organic Compound Emission Standards for Aerosol Coatings Amendments; Final Rule. 90 Fed. Reg. 5697 (January 17, 2025).
[11] U.S. Environmental Protection Agency (2025). National Volatile Organic Compound Emission Standards for Aerosol Coatings: Interim Final Rule (compliance date revised to January 17, 2027). 90 Fed. Reg. 28904 (July 2, 2025).
[12] California Air Resources Board (2023). Regulation for Reducing Emissions from Consumer Products, California Code of Regulations, Title 17, §§ 94507–94517 (Final Regulation Order, January 18, 2023). https://ww2.arb.ca.gov/sites/default/files/2023-01/Consumer%20Products%20Final%20Reg%20Order1-18-2023.pdf
[13] California Air Resources Board (2021). Final Statement of Reasons, Appendix C: Written Comments Received During the 15-Day Comment Period, Proposed Amendments to the Consumer Products Regulation (2021 rulemaking). https://ww2.arb.ca.gov/sites/default/files/barcu/regact/2021/consumerproducts2021/fsorappc.pdf
[14] Raymond, D. (2026, November 1). Regulatory Issues. Spray Technology & Marketing. https://www.spraytm.com/2026/11/01/regulatory-issues-119/
[15] California Air Resources Board (2000, amended 2001). California Procedures for Evaluating Alternative Specifications for Phase 3 Reformulated Gasoline Using the California Predictive Model. Adopted June 16, 2000; amended April 25, 2001. https://ww2.arb.ca.gov/sites/default/files/classic/isd/fuels/gasoline/meeting/2004/091504carfg3pm.pdf
[16] Code of Federal Regulations, Title 40, § 51.100(s). Definition of volatile organic compounds (VOC).
[17] U.S. Environmental Protection Agency (1977). Recommended Policy on Control of Volatile Organic Compounds. 42 Fed. Reg. 35314 (July 8, 1977).
[18] U.S. Environmental Protection Agency (1995). Air Quality: Revision to Definition of Volatile Organic Compounds: Exclusion of Acetone. 60 Fed. Reg. 31633 (June 16, 1995).
[19] U.S. Environmental Protection Agency (2012). Air Quality: Revision to Definition of Volatile Organic Compounds: Exclusion of trans-1,3,3,3-tetrafluoropropene. 77 Fed. Reg. 37610 (June 22, 2012).
[20] South Coast Air Quality Management District. Rule 102, Definition of Terms (amended March 1, 2013). https://www.aqmd.gov/docs/default-source/rule-book/reg-i/rule-102-definition-of-terms.pdf
[21] Texas Commission on Environmental Quality. Controlling HRVOC Emissions. https://www.tceq.texas.gov/airquality/stationary-rules/voc/hrvoc.html (accessed November 20, 2026).
[22] Ryerson, T.B., Trainer, M., Angevine, W.M., Brock, C.A., Dissly, R.W., Fehsenfeld, F.C., et al. (2003). Effect of petrochemical industrial emissions of reactive alkenes and NOx on tropospheric ozone formation in Houston, Texas. Journal of Geophysical Research: Atmospheres, 108(D8), 4249. https://doi.org/10.1029/2002JD003070
[23] Texas Administrative Code, Title 30, Chapter 115, Subchapter H. Highly Reactive Volatile Organic Compounds (§§ 115.720 et seq.), including § 115.722, Site-wide Cap and Control Requirements.
[24] Texas Administrative Code, Title 30, Chapter 101, Subchapter H, Division 6. Highly Reactive Volatile Organic Compound Emissions Cap and Trade Program (§§ 101.390 et seq.).
[25] Wang, L., Thompson, T., McDonald-Buller, E.C., Webb, A., and Allen, D.T. (2007). Photochemical modeling of emissions trading of highly reactive volatile organic compounds in Houston, Texas. 1. Reactivity based trading and potential for ozone hot spot formation. Environmental Science & Technology, 41(7), 2095–2102. https://doi.org/10.1021/es061273i
[26] U.S. Environmental Protection Agency, Region 6 (2023, May 8). EPA comments on TCEQ proposed revisions to 30 TAC Chapter 115. https://www.epa.gov/system/files/documents/2024-07/2023.05.08-epa-comments-on-chapter-115-jjr.pdf
[27] Texas Commission on Environmental Quality (2025). 2025 Emissions Inventory Guidelines (RG-360/25). https://www.tceq.texas.gov/downloads/air-quality/point-source/guidance/rg-360-25.pdf
[28] Carter, W.P.L., Fitz, D.R., and Cocker, D.R. (2003). Environmental Chamber Studies of VOC Species in Architectural Coatings and Mobile Source Emissions. Final report to the South Coast Air Quality Management District. College of Engineering Center for Environmental Research and Technology, University of California, Riverside. https://intra.engr.ucr.edu/~carter/epacham/scaqmdpr.pdf
[29] U.S. Environmental Protection Agency (2013). Air Quality: Revision to Definition of Volatile Organic Compounds: Exclusion of trans 1-chloro-3,3,3-trifluoroprop-1-ene [Solstice 1233zd(E)]. 78 Fed. Reg. 53029 (August 28, 2013).
[30] U.S. Environmental Protection Agency (2013). Air Quality: Revision to Definition of Volatile Organic Compounds: Exclusion of 2,3,3,3-tetrafluoropropene. 78 Fed. Reg. 62451 (October 22, 2013).
[31] U.S. Environmental Protection Agency (2018). Air Quality: Revision to the Regulatory Definition of Volatile Organic Compounds: Exclusion of cis-1,1,1,4,4,4-hexafluorobut-2-ene (HFO-1336mzz-Z). 83 Fed. Reg. 61127 (November 28, 2018).

